Product Description
Jotul 128101 Replacement Glass
Jotul Part#: 128101 includes:
- Ceramic Glass (6 1/8" x 5 7/8")
- Jotul F118
- Jotul F602 CB
- Jotul F602 v2
- Jotul F602 v3
This Part is for the Replacement Glass ONLY, if you need the glass gasket also, please order Part # 157050 Jotul Wood Stove Gasket Kit
To prevent cracking of the glass, operate the doors gently.
Do not shut the door by striking or slamming. lf the stove’s glass is cracked or broken, you must replace it before operating your stove. Carefully remove any broken pieces. Replace the panel only with the correct Jøtul replacement glass, and do not use substitutes. The glass can be replaced with the door still mounted to the stove or the door can be removed and placed on a flat working surface. The steps are the same: Clean off any residual gasket material from the door using
a wire brush if necessary. The replacement gasket is self-adhesive. Measure enough gasket to go from the upper right corner of the glass, down the right side, across the bottom and back up to the upper left corner and then add about 2-1/2”. Please note that the top of the glass is not gasketed. A small amount of air is allowed to enter through the that area to help keep the glass clean.
• Peel off about 10” of the self-adhesive backing strip. Leaving about 1-1/4” of gasket “tail” overlapping, apply the gasket to the groove on the door, making sure that the adhesive is facing the door.
• Press the gasket firmly in place.
• Peel off the remaining adhesive backing and apply the remaining gasket, again leaving a “tail” at the upper left corner.
• Press the gasket firmly in place.
• Center the glass panel left and right on top of the gasket. Slide the glass toward the bottom of the door until it hits stops.
• Hold the glass in place with your hand and wrap the gasket “tails” over the top of the glass and down the outer edges. You will have to twist the gasket so the adhesive will face the glass. Press the “tails” firmly on the glass.
• Replace the air control slide and the upper and lower retainer manifolds and screws.
To prevent cracking of the glass, operate the doors gently.
Do not shut the door by striking or slamming. lf the stove’s glass is cracked or broken, you must replace it before operating your stove. Carefully remove any broken pieces. Replace the panel only with the correct Jøtul replacement glass, and do not use substitutes. The glass can be replaced with the door still mounted to the stove or the door can be removed and placed on a flat working surface. The steps are the same: Clean off any residual gasket material from the door using
a wire brush if necessary. The replacement gasket is self-adhesive. Measure enough gasket to go from the upper right corner of the glass, down the right side, across the bottom and back up to the upper left corner and then add about 2-1/2”. Please note that the top of the glass is not gasketed. A small amount of air is allowed to enter through the that area to help keep the glass clean.
• Peel off about 10” of the self-adhesive backing strip. Leaving about 1-1/4” of gasket “tail” overlapping, apply the gasket to the groove on the door, making sure that the adhesive is facing the door.
• Press the gasket firmly in place.
• Peel off the remaining adhesive backing and apply the remaining gasket, again leaving a “tail” at the upper left corner.
• Press the gasket firmly in place.
• Center the glass panel left and right on top of the gasket. Slide the glass toward the bottom of the door until it hits stops.
• Hold the glass in place with your hand and wrap the gasket “tails” over the top of the glass and down the outer edges. You will have to twist the gasket so the adhesive will face the glass. Press the “tails” firmly on the glass.
• Replace the air control slide and the upper and lower retainer manifolds and screws.
